Resources · Whirlpool
Whirlpool Error Codes
Whirlpool shows most faults as two flashing numbers, an F code and an E code, read as one message such as F9 E1. The F number names the system and the E number narrows it down. Many of these are a hose, a filter or a vent you can check in five minutes, so try the first step before you book anyone.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM
Whirlpool front-load washers
Whirlpool says its list may not include every code for your model. To clear most of these, press Pause or Cancel twice, then Power once.
| Code | What it means | What to check |
|---|---|---|
| F5 E2 | The door is not locking properly. | Check that nothing is caught in the door and that it closes fully, then clear the code and try again. If it returns, the door lock needs testing. |
| F7 E1 | The washer is having trouble sensing motor speed. | Confirm the shipping bolts were removed at installation and the drum is not overloaded. |
| F8 E1 / LO FL | Water is arriving too slowly. | Open both the hot and cold taps fully, check the fill hoses for kinks, and look for anti-flood devices in the supply line. |
| F8 E2 | A problem in the detergent dispenser system on some models. | Pull the dispenser and clean out any caked detergent. |
| F9 E1 | The washer is taking too long to drain, typically more than 8 minutes. | Check the drain hose for kinks, use the U-shaped hose guide, make sure the standpipe height is within the installation range, and use HE detergent only. |
| Sud / Sd | Too many suds. The washer extends the rinse automatically. | Use HE detergent and the right amount. Switch from no-splash bleach to regular liquid bleach. |
| Any other F# E# | A fault the control has detected that is not on the list above. | Cut power for 5 minutes, restore it, reselect the cycle and press Start. If the same code comes back, it needs service. |
Whirlpool dryers
A flashing F# and E# pair alternating on the display means the control has found a fault that needs service.
| Code | What it means | What to check |
|---|---|---|
| AF / F30 | Restricted airflow. The lint screen is clogged, or the vent is blocked, crushed, kinked or has too many bends. | Clean the lint screen, then check the vent behind the dryer. A blocked vent is also a fire risk, so do not keep running the dryer on it. |
| F3 E1 | A fault with the exhaust thermistor, the sensor that watches the air leaving the dryer. | Switch the dryer breaker off for one minute, restore it, and run a timed dry. If the code returns, the sensor circuit needs testing. |
| F1 E1 | The control reports an internal fault. | Switch the breaker off for 5 minutes, restore it and run a timed dry cycle. If it returns, it needs a technician. |
| L2 | Low or no line voltage, shown during first installation. | Check for a tripped breaker or blown fuse (electric dryers use two) and that the power cord is connected as the installation sheet shows. If it persists, call an electrician. |
| PF | A power failure interrupted the cycle. | Touch and hold Start to restart the cycle, or press Power to clear the display. |
Whirlpool dishwashers
Dishwasher codes flash in two groups. Count the first set of flashes for the F number, pause, then count the second set for the E number.
| Code | What it means | What to check |
|---|---|---|
| F9 E1 | The dishwasher is not draining. | Clean the filter under running water, check the drain hose for kinks, make sure the disposer is clear and its knockout plug was removed, and clear the air gap if you have one. |
| F8 E4 | Water has been detected in the drip tray. | Turn off the water. Look for a leak at the connections and the door seal. Do not keep restarting the machine. |
| F7 E2 | Wash motor error. | Power cycle the dishwasher for 30 seconds. If the code returns, it needs service. |
| F6 E1 | A user-interface or main control error. | Power cycle the dishwasher. If it returns, the control needs testing. |
| H20 | The dishwasher is not detecting water. | Make sure the water supply valve is open and the supply hose is not kinked. |
Codes vary by model and year. If your code is not listed, call (619) 743-9389 with the model number. See also Whirlpool appliance repair in San Diego.
FAQ
Whirlpool code questions
How do I read a Whirlpool F and E code?
The F number and the E number are two parts of one message. On a washer they alternate on the display, as in F9 E1. On a dishwasher they flash as two groups of lights, so count the first group, wait for the pause, then count the second.
Why does my Whirlpool dryer say AF when the lint screen is clean?
AF means airflow is restricted somewhere past the screen. The usual cause is the vent run itself: lint packed in the duct, a crushed section behind the dryer, or a blocked outside cap. A clean screen with an AF code points to the vent.
Is it safe to keep using a Whirlpool washer that shows F5 E2?
The washer is refusing to run because the door is not confirmed locked, which is a safety feature. Check the door first. If the code returns on every load, the door lock needs replacing before the washer will work.
Whirlpool code will not clear? Book a diagnostic.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM. San Diego and Orange County.
Call us for a diagnosis.