Resources · GE
GE Error Codes
GE codes depend on the appliance more than the brand. A dishwasher uses C numbers, a washer shows plain Consumer Help messages, and a range uses F numbers that mostly point to a keypad, a sensor or a lock. Check the first step, then reset at the breaker. If the code returns, it is real.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM
GE dishwashers
Disconnecting power at the breaker for a minute or two clears many dishwasher codes.
| Code | What it means | What to check |
|---|---|---|
| C1 | The pump-out during drain ran longer than 2 minutes. | Clean the air gap, check the drain hose and run the disposer to clear it. |
| C2 | The total pump-out cycle ran longer than 7 minutes. | Press Reset to stop the beep, then check the drain path. |
| C3 | The dishwasher will not drain. | Turn off the breaker for about 30 seconds, restore it and reset. If the code returns, call. |
| C4 | The machine filled twice after a power failure, the float is stuck, or the drain or sump is clogged. | Tap the float cover to free it and look in the sump for debris. |
| C5 | The pump-out time was too short. | Make sure the water supply is on, run the cycle again, and tap the float cover. |
| C6 | The incoming water is too cold. | Run the nearby hot tap before starting, and avoid using hot water elsewhere during the cycle. |
| C7 | The water temperature sensor circuit is not working. | Reset at the breaker. If it returns, it needs service. |
| C8 | The detergent cup is blocked from fully opening. | Remove anything blocking the cup, close the door and wait 30 seconds. |
| H2O | Low water level. | Check the inlet hose is not kinked. If it appears only on the 1-hour wash, that cycle needs service but others can be used. |
| LEAK DETECTED / 999 | A possible leak was detected on models with leak protection. | Turn off the water and call. The dishwasher will not start on these models. |
GE washers
These Consumer Help messages appear on electronic-control GE washers. Messages vary by model.
| Code | What it means | What to check |
|---|---|---|
| UE | The load is unbalanced. | Spread the laundry evenly and make sure the washer is level. |
| H2O SUPPLY / IE | Water is not entering the washer. | Check both house supply valves are on. The washer locks out for 4 minutes before it will retry. |
| FE | Water has reached a critical level. | Turn off the water and the power, then call for service. |
| Lid | Three cycles were started without opening the lid. | Open the lid, close it and start a new cycle. |
| CAnCELEd | The washer was paused for more than 24 hours, or stopped itself because of an error. | Wait out the 4-minute lockout and start the cycle again. |
GE ranges and wall ovens
Turn off the oven breaker for a minute or two. If the code returns, GE says a service technician is needed. Keep the oven off at the breaker until then.
| Code | What it means | What to check |
|---|---|---|
| F0 / F1 / F6 / F7 | A keypad problem, often needing the keypad replaced. | Check nothing is pressing a key and the panel is dry. If it returns, it needs service. |
| F2 / F20 | The oven temperature exceeded a preset limit. | Turn off the oven at the breaker and call. Do not keep using it. |
| F3 / F4 | The oven temperature sensor usually needs replacing. | This needs a technician. |
| F5 / F8 / FF | The electronic control usually needs replacing. | This needs a technician. |
| F9 / FC | A part in the door lock circuit has failed. | This needs a technician. |
| Bad Line | Power is connected but the unit is wired incorrectly. | An installer or electrician needs to correct the wiring. |
| LOC | Child lockout is on. Not a fault. | Check your owner's manual for the unlock sequence. |
Codes vary by model and year. If your code is not listed, call (619) 743-9389 with the model number. See also GE appliance repair in San Diego.
FAQ
GE code questions
What does C3 mean on a GE dishwasher?
It means the dishwasher will not drain. Turn the breaker off for about 30 seconds, restore power and reset it. If C3 returns, check the air gap and drain hose, then call for a drain pump diagnosis.
Why does my GE oven show F9?
F9 points to the door lock circuit. The oven control cannot confirm the lock position. Reset at the breaker once, and if the code comes back, the lock assembly needs testing.
Do GE microwave F codes mean the same as oven F codes?
No. GE says F1, F2 and F3 mean different things on microwaves and Advantium ovens than they do on ranges and wall ovens. Match the code to the exact appliance.
GE code will not clear? Book a diagnostic.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM. San Diego and Orange County.
Call us for a diagnosis.