Resources · LG
LG Error Codes
LG appliances show short letter codes. Most point clearly to one system, which makes them among the easiest to read. These are the codes San Diego customers ask us about most.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM
LG washers
| Code | What it means | What to check |
|---|---|---|
| OE | The washer cannot drain. | Clean the drain pump filter at the bottom front and check the drain hose is not kinked or pushed too far into the standpipe. |
| UE / uE | The load is unbalanced. | Redistribute the load and avoid washing one heavy item alone. If it happens on every load, the suspension or the level needs attention. |
| IE | Water is not entering fast enough. | Check the taps are fully open and clean the inlet hose screens. Hard-water scale often blocks them. |
| LE | The motor is locked or overloaded. | Unplug for 30 minutes and try a smaller load. If it returns, the motor, rotor position sensor or wiring needs testing. |
| dE / dE1 / dE2 | The door is not closed or locked. | Close the door firmly and check for clothing in the seal. Otherwise the door lock has failed. |
| FE | Overfill: too much water in the drum. | Turn off the taps. The inlet valve is probably stuck open and needs replacing. |
| PE | Water level sensor fault. | Needs a technician: the pressure sensor or its hose. |
| tE | Temperature sensor fault. | Needs a technician: the thermistor or the heater circuit. |
| CL | Child lock is on. This is not a fault. | Hold the Child Lock button for three seconds. |
LG dryers
The d-codes are the most useful codes any dryer shows. They tell you the dryer is fine and the vent is not.
| Code | What it means | What to check |
|---|---|---|
| d80 | The exhaust is about 80 percent blocked. | Clean the lint filter and have the vent cleaned from the dryer to the outside. |
| d90 / d95 | The exhaust is 90 to 95 percent blocked. | Stop using the dryer until the vent is cleaned. This is a fire risk. |
| tE1 / tE2 / tE3 | A temperature sensor (thermistor) fault. | Needs a technician. |
| PS | The power cord is wired incorrectly or the supply voltage is wrong. | Have the cord connection and outlet checked. |
LG refrigerators
| Code | What it means | What to check |
|---|---|---|
| Er IF / 1F | Ice-room fan fault. | Often ice around the fan. Needs defrosting and the cause found. |
| Er FF | Freezer fan fault. | Ice build-up or a failed fan motor. |
| Er CF | Condenser fan fault. | Check for dust or an obstruction at the back. Otherwise the fan motor. |
| Er dH | The defrost cycle did not complete. | Defrost heater, fuse or sensor. Needs a technician. |
| Er CO | Communication error between control boards. | Power off for five minutes. If it returns, wiring or a board. |
| Er FS / Er rS | Freezer or refrigerator temperature sensor fault. | Needs a technician. |
Codes vary by model and year. If your code is not listed, call (619) 743-9389 with the model number. See also LG appliance repair in San Diego.
FAQ
LG code questions
What does OE mean on an LG washer?
OE means the washer could not drain in time. Clean the drain pump filter and check the drain hose. If the pump hums but no water moves, the pump needs replacing.
My LG dryer shows d80. Is the dryer broken?
No. d80 means the dryer has detected a blocked exhaust. The dryer is working. The vent needs cleaning from the dryer to the outside.
How do I reset an LG appliance after an error?
Unplug it or switch off the breaker for a few minutes, then restore power. If the fault is still present, the code will come back.
LG code will not clear? Book a diagnostic.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM. San Diego and Orange County.
Call us for a diagnosis.