Resources · KitchenAid
KitchenAid Error Codes
KitchenAid is part of the Whirlpool family, so its codes follow the same F-and-E format. The dishwashers flash a count of lights, the refrigerators flash a single F when something needs a reset, and the washers show F# E# pairs on the display. The tables below list the ones with a clear first step.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM
KitchenAid dishwashers
Count the first set of flashes for the F number, pause for 1 to 2 seconds, then count the second set for the E number. The pattern repeats after about 5 seconds.
| Code | What it means | What to check |
|---|---|---|
| F9 E1 | The dishwasher is not draining. | Clean the filter, check the drain hose for kinks, make sure the disposer is clear and its knockout plug was removed, and check any air gap. |
| F8 E4 | Water has been detected in the drip tray. | Turn off the water. Check the connections for a leak and empty the tray. Do not keep restarting the dishwasher. |
| F7 E2 | Wash motor error. | Disconnect power for 30 seconds. If the code returns, it needs service. |
| F6 E1 | A user-interface or main control error. | Cycle the power. If it returns, the control needs testing. |
| H20 | The dishwasher is not detecting water. | Open the supply valve and check the supply hose for kinks. |
KitchenAid refrigerators
Codes vary a lot by model. The service documentation for some models uses shorthand such as SH for a shorted sensor and OP for an open one.
| Code | What it means | What to check |
|---|---|---|
| Flashing F | The control has detected a fault and asks for a power reset. | Unplug the refrigerator or switch the breaker off for about a minute, restore power, confirm cooling is on, and watch for a minute to see whether it returns. |
| F3 E1 / F3 E2 / F3 E3 | A temperature sensor fault: E1 in the fresh-food compartment, E2 in the freezer, E3 in the convertible compartment, on models that use them. | Power reset first. If it returns, the sensor or its connection needs testing. |
KitchenAid washers
KitchenAid laundry is built by Whirlpool and uses the same F-and-E messages. Clear most of them by pressing Pause or Cancel twice, then Power once.
| Code | What it means | What to check |
|---|---|---|
| F5 E2 | The door is not locking properly. | Close the door fully and check nothing is caught in it. |
| F8 E1 | Water is arriving too slowly. | Open both taps fully and check the fill hoses for kinks. |
| F9 E1 | The washer is draining too slowly. | Check the drain hose for kinks and use HE detergent only. |
| Any other F# E# | A fault the control has detected. | Cut power for 5 minutes and restart. If it returns, it needs service. |
Codes vary by model and year. If your code is not listed, call (619) 743-9389 with the model number. See also KitchenAid appliance repair in San Diego.
FAQ
KitchenAid code questions
How do I read a KitchenAid dishwasher flash code?
Count the first group of flashes. That is the F number. Wait for the 1 to 2 second pause and count the second group. That is the E number. The sequence repeats after a longer pause, so you can count it again to be sure.
My KitchenAid refrigerator shows a flashing F. Should I call?
Try a power reset first: unplug it or switch the breaker off for about a minute, then check that cooling is on. If the F comes back within a minute or two, or a number follows it, that is a real fault.
Why does my KitchenAid dishwasher show F9 E1 when it was draining yesterday?
Something has partly blocked the path: the filter, a kinked hose, or the disposer knockout plug on a new disposer. Check the filter first. It is the most common cause and takes two minutes.
KitchenAid code will not clear? Book a diagnostic.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM. San Diego and Orange County.
Call us for a diagnosis.