Resources · Frigidaire
Frigidaire Error Codes
Frigidaire keeps its codes simple. A top-load washer reports E1 to E5 for fill, drain, lid, balance and level, a dishwasher reports i20 or i40 for drain problems, and a refrigerator mostly signals alarms rather than faults. Many of these clear once you find the kink, the filter or the open door.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM
Frigidaire top-load washers
Front-load Frigidaire washers use a different list that varies by model. Check the manual or call with the model number.
| Code | What it means | What to check |
|---|---|---|
| E1 | The washer is taking too long to fill. | Open both taps fully and clean the hose screens. Low water pressure can also be the cause. |
| E2 | Water is taking too long to drain. | Check the drain hose for kinks and make sure it is seated correctly in the standpipe. |
| E3 | The lid is open or the lid lock failed to latch. | Close the lid fully and check nothing is caught under it. If the lid is clear and the code returns, the lid lock needs testing. |
| E4 | The load is out of balance. | Redistribute the clothes and avoid washing one heavy item alone. |
| E5 | The washer is not level. | Adjust the feet until the washer does not rock. Check all four corners. |
| F2 | Too many suds, or suds overflowing. | Use HE detergent and the labelled amount. |
| CL | The lid was opened for more than 20 seconds while control lock was on. | Turn the control lock off. |
Frigidaire dishwashers
| Code | What it means | What to check |
|---|---|---|
| i20 | The dishwasher did not drain completely. | Check the disposer knockout plug is removed, the drain hose is not blocked or pinched, and clear any debris from the filters and sump. |
| i40 | The filter or sump is clogged. | Clean the glass trap and filter, then run the cycle again. |
| CL / Cd | The door is not fully closed and latched. | Close and latch the door. If it will not close, it needs service. |
| Hd / HO | Heat delay or heater on. This is normal while the water heats. | No action needed. Cold supply water takes longer. |
| PF | Power was lost during the cycle. | Press Start/Cancel to clear it, then start a new cycle. |
Frigidaire refrigerators
To reset, press Clear Alerts if your model has the button. Otherwise unplug the unit for 30 seconds.
| Code | What it means | What to check |
|---|---|---|
| HI / H | The temperature stayed too high for over an hour, often after a door was left open. | Make sure both doors are fully closed and sealed, then give the fridge time to recover. |
| Door Ajar | A door has been open for more than 5 minutes. | Close the door. |
| DISP | Ice is jammed in the dispenser chute. | Clear stuck cubes. If it continues, empty the ice bin, let it thaw and dry, and put it back. |
| PF | A power outage or surge. | It can also trigger a high-temperature alarm. Let the fridge recover and check food. |
| SB SB / 77 77 | Sabbath mode (SB) or demo mode (77 77). Not faults. | Sabbath mode is turned off by holding the two buttons the manual names. To exit demo mode, unplug the unit for 5 minutes. |
Frigidaire electric ranges
Frigidaire lists these range codes by name. Turn the range off at the breaker for a minute if one appears, and call if it returns.
| Code | What it means | What to check |
|---|---|---|
| F1 | Shorted keypad. | Make sure nothing is pressing a key and the panel is dry, then reset at the breaker. |
| F10 | Thermal runaway: the oven heated beyond its limit. | Turn the oven off at the breaker and call for service. Do not use it. |
| F30 / F31 | The oven probe is open (F30) or shorted (F31). | Unplug the meat probe if you use one, then reset at the breaker. |
| F90 to F94 | A door lock problem. | Make sure the door is not blocked. If the code returns, the lock needs testing. |
Codes vary by model and year. If your code is not listed, call (619) 743-9389 with the model number. See also Frigidaire appliance repair in San Diego.
FAQ
Frigidaire code questions
What does i20 mean on a Frigidaire dishwasher?
It means the water did not drain completely. Start with the disposer knockout plug, which is still in place on many new installs, then the drain hose and the filters. If all three are clear, the drain pump needs checking.
Why does my Frigidaire refrigerator show HI?
The inside has been too warm for more than an hour. A door left open is the usual cause. If both doors are closed and the code stays after a few hours, the cooling system needs a diagnosis.
How do I reset a Frigidaire appliance?
Use the Clear Alerts button if there is one. Otherwise unplug the appliance for 30 seconds. If you flip the breaker instead, you reset everything on that circuit.
Frigidaire code will not clear? Book a diagnostic.
Open 7 days Mon–Fri 7 AM–10 PM · Sat 8 AM–10 PM · Sun 8 AM–8 PM. San Diego and Orange County.
Call us for a diagnosis.