+1 619-743-9389
Kenmore Appliance Fault Code Help Resource
When a Kenmore appliance shows an error code, it usually means the unit has detected a problem in one of its main systems. On Kenmore dishwashers, washers, dryers, ranges, wall ovens, refrigerators, and freezers, these codes usually point to control-board faults, user-interface problems, drain issues, water-level errors, sensor failures, door-lock problems, or temperature-related faults.
This page gives homeowners in San Diego a clear overview of the main Kenmore appliance error code patterns. It is meant to help you understand what the code is usually pointing to and when it makes sense to request service.
Reset Appliance Repair provides local appliance repair in San Diego for major household appliances, including Kenmore dishwashers, top load washers, front load washers, dryers, ranges, wall ovens, refrigerators, and freezers.
What Kenmore Appliance Error Codes Usually Mean
A Kenmore error code is not always a final diagnosis. In most cases, it helps narrow the issue to one system. One code may point to a control problem. Another may indicate a drain fault, a lock issue, a sensor failure, or a temperature-related problem.
Reading Kenmore codes by family makes them easier to understand. Across Kenmore appliances, the main patterns usually involve electronics, controls, water fill, draining, locking, sensing, and communication faults.
Common Kenmore Appliance Error Code Families by Appliance Type
Kenmore Dishwasher Error Code Families
Control, user-interface, and sensor-related codes: 1-1 / F1E1 / 1-2 / F1E2 / 2-1 / F2E1 / 2-2 / F2E2 / 3-1 / F3E1 / 3-2 / F3E2 / 4-1 / F4E1
This is the main Kenmore dishwasher code family in your list. These codes usually point to a stuck relay, damaged control-board memory, stuck button, communication fault between the user interface and main control, thermistor or OWI sensor failure, or a circulation-pump communication error. In daily use, that may show up as a dishwasher that will not start correctly, behaves unpredictably, or stops mid-cycle.
Kenmore Top Load Washer Error Code Families
Control, sensor, and lid-related codes: F1 E1 / F1 E2 / F2 E1 / F2 E3 / F3 E1 / F3 E2 / F5 E1 / F5 E2
This is the main Kenmore top load washer code family because it covers the most important wash-cycle problems. These codes usually point to a main control-board failure, motor-control problem, stuck key, control mismatch, water-level pressure-sensor fault, inlet temperature issue, lid-switch fault, or lid-lock problem. In home use, that can mean the washer will not start properly, cannot sense water conditions correctly, or cannot continue the cycle safely.
Kenmore Front Load Washer Error Code Families
Drain, fill, lock, and water-level related codes: nd / LO / nF / FL / LE / lE / OE / E2
This is one of the most useful Kenmore front load washer code groups for everyday laundry problems. These alerts usually point to a drain problem, door unlock or lock error, water-fill issue, low water level during the cycle, water-level sensor failure, overflow condition, or a stuck button. In daily use, that may show up as water left in the drum, a cycle that will not start, or a washer that stops before completion.
Kenmore Dryer Error Code Families
Control, thermistor, heater, and moisture-sensor codes: F:01 / F:02 / F:20 / F:22 / F:23 / F:24 / F:25 / F:28 / F:29
This is the main Kenmore dryer code family in your list. These codes usually point to a main electronic control-board fault, keypad problem, heater relay failure, inlet or outlet thermistor fault, or moisture-sensor problem. If the same code keeps returning, the dryer usually needs more than a reset.
Kenmore Range and Wall Oven Error Code Families
Touch panel, user-interface, and temperature-related codes: F001 / F002 / F003 / F004 / F005 / F010 / F011 / F013 / F015 / F017
This is the main Kenmore cooking-appliance code group. These alerts usually point to a touch-panel failure, user-interface board problem, runaway temperature condition, stuck keypad key, or a UI board that cannot configure the touch panel. If these codes repeat, the range or wall oven may not respond normally or may have trouble heating safely.
Kenmore Refrigerator Error Code Families
Thermistor, sensor, and communication-related codes: C / CF / OP / Er FS / Er rS / F dS
This is one of the most important Kenmore refrigerator code groups because it points to refrigerator or freezer thermistor faults, communication problems between the main board and user interface, open temperature sensor conditions, or a freezer defrost sensor problem. In daily use, that can show up as unstable cooling, incorrect temperature readings, or a refrigerator that is no longer managing normal food-storage conditions.
Other Kenmore refrigerator code groups
Air damper code: d
Kenmore Freezer Error Code Families
Communication, stuck-key, thermistor, and high-temperature codes: CE / E7 / E8 / E9 / Temperature flashing + control beeps / d
This is the main Kenmore freezer code family in your list. These alerts usually point to a communication error, stuck key, defective thermistor, high freezer temperature, or a door or door-switch problem. In normal use, that may show up as warming food, unstable freezer temperature, or controls that do not respond correctly.
What Homeowners in San Diego Should Do First
Check how the appliance is behaving along with the code. Look for poor draining, fill problems, door or lid issues, temperature warnings, sensor-related problems, or a cycle that stops before completion. If the same code keeps returning or the appliance is no longer working normally, the problem usually needs proper diagnosis.
Local Kenmore Appliance Error Code Help in San Diego
Repeated Kenmore error codes usually mean the appliance needs more than a reset. If your Kenmore dishwasher, washer, dryer, range, wall oven, refrigerator, or freezer keeps showing the same alert, local in-home service can help identify the cause and the next repair step.
Reset Appliance Repair – San Diego, CA
📍 Address: 11031 Via Brescia, San Diego, CA 92129
📧 Email: resetappliance@gmail.com
☎️ Phone: +1 619-743-9389
🕒 Open Hours: Monday – Sunday: 7:00 AM – 10:00 PM
Kenmore Appliance Error Code Table Based on Official Support Information
The table below summarizes common Kenmore appliance error codes, the appliance type they apply to, what each code usually means, safe first steps, and when technician service may be needed. This information is organized from official Kenmore support resources, manufacturer-related appliance documentation, and model-specific troubleshooting guidance where available, then simplified for San Diego homeowners who need to understand dishwasher, washer, dryer, range, wall oven, refrigerator, and freezer alerts before requesting repair service. For more detailed information about your exact Kenmore appliance model, error-code meaning, and official troubleshooting guidance, you can visit the official Kenmore support page.
| Error Code | Appliance | Meaning | Safe first steps | Technician required | Related help |
|---|---|---|---|---|---|
| CE | Refrigerator | Deluxe electronic-control freezer. Communication error between control panel and electronic control board | Unplug freezer for 1 minute and retry once. | Yes — if the code returns after the safe checks. | |
| d (refrigerator display) | Refrigerator | [106 side-by-side] Air damper is stuck | Unplug refrigerator and check for obvious air-damper damage or obstruction. | Yes — if the code returns after the safe checks. | |
| C (refrigerator display) | Refrigerator | Refrigerator compartment thermistor failure | Unplug refrigerator and inspect the thermistor harness for obvious looseness. | Yes — if the code returns after the safe checks. | |
| F001 / F002 / F004 / F005 | Range and Oven | [790 4-digit range] Touch panel failure | Disconnect power for 30 seconds and retry once. | Yes — if the code returns after the safe checks. | |
| F003 | Range and Oven | [790 4-digit range] User interface control board failure | Disconnect power. If code returns, service should replace the UI board. | Yes — if the code returns after the safe checks. | |
| F:01 | Dryer | [Elite dryer] Main electronic control board failure | Unplug for 5 minutes and retry once. | Yes — if the code returns after the safe checks. | |
| F:02 | Dryer | [Elite dryer] Keypad / user interface failure | Try freeing a stuck key if obvious. If not resolved, service is needed. | Yes — if the code returns after the safe checks. | |
| tE3 | Dryer | [Hybrid dryer] Heater thermistor failure | Unplug dryer and stop use until thermistor wiring/resistance is checked. | Yes — if the code returns after the safe checks. | |
| nd | Washer | Won't drain | Check drain path and clean the pump filter / large-item filter if accessible. If still not draining, service the pump. | Yes — if the code returns after the safe checks. | |
| LO | Washer | Door unlock error | Unplug washer. If the door remains locked or the lock assembly is damaged after opening, service is required. | Yes — if the code returns after the safe checks. | |
| F1 E1 | Washer | Main electronic control board failure | Unplug washer and check for obviously loose console wiring only. | Yes — if the code returns after the safe checks. | |
| F1 E2 | Washer | Motor control error on main electronic control board | Unplug washer. If wiring to motor/control is not visibly loose, schedule service. | Yes — if the code returns after the safe checks. | |
| 1-1 / F1E1 | Dishwasher | Stuck relay on the electronic control board | Shut off power for 5 minutes. If the code returns, inspect control-board wiring for damage before service diagnosis. | Yes — if the code returns after the safe checks. | |
| 1-2 / F1E2 | Dishwasher | Damaged or corrupted memory on control board | Shut off power for 5 minutes. If the code returns, service should replace the electronic control board. | Yes — if the code returns after the safe checks. |
